DNP或3nh标准灯箱 DNP Standard Color Viewer
欢迎电话咨询:黄工13510847162
3nh 或 DNP标准灯箱 3nh & DNP Standard Color Viewer
产地:OEM 或 日本
技术参数
DNP标准颜色Viewer
是摄影机及静相摄影机的评价,调整用的光源装置。
能看由于高频荧光灯点灯方式的采用闪烁不定没有的画像。
方法:
光源: DNP标准颜色viewer油灯
(特殊荧光管10W×4个使用)
电源: AC100v50,60Hz
点灯方式: 高频点灯方式20KHz
演颜色性: 对各颜色演颜色评价点90以上
色温: (美能达制CL-200测量)
使用温度: 10~40〓C
使用湿度: 80%以下(结露没有事)
外形尺寸: 375W×365H×165D m/m
亮度方面尺寸: 250W×190H m/m
海图尺寸: 320W×290H m/m
消耗功率: 80W
重量: 6.5kg/7.5kg
由于viewer包藏荧光油灯的差异的亮度方面的特性
对待说明
【1】 使用前
电源:AC电源100v,50Hz,60Hz共用
光源:DNP标准颜色viewer油灯 10W×4个
消耗功率:80W
【2】 使用
(1) AC100v的插座插入电源编码的插头。
※注意: AC100v以外的电源请别连接。
在海外利用时候,必定拜托您了变压器的使用。
变成弄错AC100v以外的电源连接的话被安上内部取的变压器的烧毁。
(2) ON电源开关。
(3) 以油灯点灯常温(20℃)点灯后15~20分稳定。
(4) 油灯不点灯的时候,向别的项目的大街电保安人员要求请求确认。
(5) 油灯的胫―王现象发生了的时候修好做电源开关3~4次ON,OFF。
【3】 油灯不点灯的时候
请在电保安人员确认。
(1) 插座AC100v通上电流。
(2) 插座插入viewer的插头。
(3) viewer的电源开关ON。
Viewer的油灯不点灯的时候,能考虑象下面一样的事
(1) 油灯2盏点灯的时候,变压器的一方的保险丝溶断做着。
(2) 油灯4盏是不点灯的时候,2台变压器的各々的保险丝溶断做着。
※注意: 上述(1)(2)AC100v以外的通电的时候发生。这变压器内部烧毁是原因。
变压器的交换变成必要。
【4】 与油灯的交换清扫
在平的台里(上)放置viewer从插座上请取下电源编码。
以下面的顺序进行卸载。
(1) 放松上面框框的硬币螺钉2处。
(2) 用双手举起50~60毫米上面框框的硬币螺钉方面推到前方的话上面框框偏离实体。
(3) 取下玻璃板和丙烯板。
※注意: 玻璃板因为有破裂请当心手手指。
(特别象用手手指不擦一样地请注意板边方面。)
■油灯交换
(1) 又,1年流逝的时候点灯2,000小时。
(2) 脱离用双手手指夹油灯的管端部使之转90〓。
■清扫工作
(1) 请在纱布中浸湿酒精擦去反射板表面,丙烯板和玻璃表面的污秽取。
(2) 清扫为了6个月~1年1次,正常保持色温,亮度无论如何拜托您了。
【5】 使用前
viewer因为使用着玻璃品请注意下面的事。
(1) 请别给(对)viewer实体给予大的冲击。
(2) 请别搁置对viewer表面沉重的东西。
DNP Standard color Viewer |
 |
|
|
 |
The DNP Standard color Viewer is a light source which enables you to evaluateadjust videostill cameras. With its high-frequency Fluorescent lighting method, it handles images without flicker. |
Specification
Light source: |
DNP Standard color Viewer lamp
(Four 10W dedicated fluorescent tubes are used) |
Power supply: |
AC100V 50, 60Hz |
Lighting method: |
High Frequency lighting method 20KHz |
Color rendering: |
Over 90% rendering evaluation-point for each color |
Color temperature: |
(Measured by Minolta CL-200) |
Operating temperature: |
10~40℃ |
Operating humidity: |
Below 80%(avoid dew) |
Major diameter dimension: |
375W×365H×165D m/m |
Luminance plane dimension: |
250W×190H m/m |
Color chart dimension: |
320W×290H m/m |
Power consumption: |
80W |
Weight: |
6.5kg/7.5kg |
●The Luminance plane characteristics: according to the types of self-contained fluorescent lamp |
 |
Product Type |
Luminance Color Temperature |
Lamp |
Color Temperature |
Luminance |
Color matching shift |
Weight |
CCV-31F |
Fixed |
FL10WW-DLB |
3100K±300 |
Over 1300cd/m2 |
Within 10% |
6.5kg |
CCV-51F |
Fixed |
FL10D-EDL-56K |
5100K±300 |
Over 1400cd/m2 |
Within 10% |
6.5kg |
CCV-31F/G |
Volume adjustable |
FL-10WW-DLB |
3100K±300 |
Over 850~1300cd/m2 |
Within 10% |
7.5kg |
CCV-51F/G |
Volume adjustable |
FL10D-EDL-56K |
5100K±300 |
Over 850~1400cd/m2 |
Within 10% |
7.5kg |
|
 |
*The color temperature if Luminance. Color Temperature Conversion Type viewer ranges over 50k according to the change of the Luminance.
*The specification may change without notice |
 |
|
 |
【1】 |
Before using the product: |
 |
|
Power supply |
 |
AC 100V, 50/60Hz shared |
Light source |
 |
10W DNP Standard color Viewer Lamp (4) |
Power consumption |
 |
80W |
|
 |
【2】 |
Using the DNP Standard color Viewer |
 |
|
(1) |
Plug the power cable of the product into AC100V |
|
|
【Precautions】 |
Do not connect any power supply other than AC100V
If the other power supply connected by accident, the inverter inside will burned out |
|
|
(2) |
Turn on the power switch |
|
(3) |
Lamp lights: the lamp light will stabilised after 15 to 20 minutes at the room temperature(20℃) |
|
(4) |
If the lamp does not lit, call for Service Office for the confirmation as described on other documents. |
|
(5) |
To suspend snaking of the lamp, press power switch 3 to 4 times [as ON/OFF]. |
|
 |
【3】 |
If the light does not lit |
 |
|
Call for Service Office to confirm the following: |
|
(1) |
AC 100V supplied to the wall socket. |
|
(2) |
Plug the product into the wall socket. |
|
(3) |
Turn the power supply switch of the product ON |
 |
|
|
 |
 |
|
Still the lamp does not lit: Consider the following: |
 |
|
|
 |
 |
|
(1) |
Two of the viewer lamps lit simultaneously, one of the fuses of the inverters has blowouts. |
|
(2) |
Four of the viewer lamps does not light means that each of the fuses of the two inverters has blowouts. |
|
|
【Precautions】 |
The above occurs if the applied power supply is not AC 100V.
Fuse bum out cause internal burnout of inverter. The burned inverter needs to replace. |
|
|
 |
【4】 |
How to replace the lampkeep it clean |
 |
|
Place the Viewer on the flat table,plug out the power supply cable from the wall socket.
Remove the used device in the following order: |
|
(1) |
Unfasten the two of grub screws on the top frame. |
|
(2) |
To remove the top frame from the main unit;
Holding 50 to 60 mm the grub screw of the top framepress it forward. |
|
(3) |
Remove the glass plateacrylic plate. |
|
|
【Precaution】 |
Glass plate easily breaksmay hurt your handsfingers.
Handle the edge of the plate with care not to scratch. |
|
 |
|
◆Replacing the lamps: |
|
(1) |
When the lamps used over 2,000 hours or one year, it needs to replace. |
|
(2) |
Remove the Lamp Tubes: Hold the edge of the Lamp Tubes,turn it 90 degree. |
 |
|
◆Cleaning the device: |
|
(1) |
Impregnate alcohol to gauze then apply it onto the surface of the reflection plate / acrylic plate / glass surface to remove the dirt. |
|
(2) |
Clean the device once in six months to one year to keep quality of the Color TemperatureLuminance. |
|
 |
【5】 |
Other Precautions |
 |
|
Handling the viewer needs the following precautions because it contains the parts using glass. |
|
(1) |
Do not add strong impact on the viewer |
|
(2) |
Do not put any heavy items on the surface of the viewer |
|